• Federal Premium Brass 270 Winchester Short Magnum (WSM) Bag of 50

    Federal Premium Brass 270 Winchester Short Magnum (WSM) Bag of 50

    Federal is known for loading some of the best factory ammunition available and this brass is no different. This brass is manufactured to the same high standards and consistency that have made Federal Premium Ammunition one of the favorites of shooters everywhere. This is not loaded ammunition.

    Brass Preparation: With bulk rifle brass you may sometimes notice a few case mouths are “out of round” or slightly dented below the shoulder.  These imperfections occur in the final tumbling wash operation after the case mouth has been annealed.  Brass manufacturers are aware of the case cosmetics and have worked to mitigate it, but due to equipment design, denting may still occur.  Minor dents are normally removed in the first firing and will not affect case life or performance.  On non-plated brass, you may also notice all the anneal stain might not be polished off, which may give the case neck a pinkish color.  With some smaller caliber cases you may notice the case mouths to be slightly belled.

    With all new rifle brass, you should first straighten out the case and case mouth, then chamfer and debur the case mouth inside and out.  To straighten the case mouth, run the case part way into the sizer die and let the expander ball straighten the brass.  To prevent the case neck from stretching, be sure to lubricate the case neck inside the case mouth.

    CAD $74.25
    Add to cart

    Federal Premium Brass 270 Winchester Short Magnum (WSM) Bag of 50

    CAD $74.25 Add to cart
  • Once Fired Brass 380 ACP Grade 2 (Bulk)

    Once Fired Brass 380 ACP Grade 2 (Bulk)

    This brass comes from indoor ranges and may have minor dings, dents or slight imperfections. Most flaws can be easily removed upon resizing or will be shot out upon the first firing. This brass has not been re-sized and must be full-length sized and trimmed before loading the first time. Grade 2 Brass has been tumbled but not yet deprimed. Brass is sold as-is.

    CAD $74.25
    Add to cart

    Once Fired Brass 380 ACP Grade 2 (Bulk)

    CAD $74.25 Add to cart
  • Remington Brass 270 Winchester Short Magnum (WSM) Bag of 50

    Remington Brass 270 Winchester Short Magnum (WSM) Bag of 50

    Remington cartridge cases are carefully drawn from specially-alloyed brass to provide consistently exact internal volume and resistance to case stretching and brittleness. Primer pocket tolerances are held to .001″, and closely monitored case neck annealing ensures easier re-sizing and longer reloading life. New, unprimed brass. This is not loaded ammunition. Bulk brass should be full-length sized, trimmed and chamfered before loading.
    Brass Preparation: With bulk rifle brass you may sometimes notice a few case mouths are “out of round” or slightly dented below the shoulder.  These imperfections occur in the final tumbling wash operation after the case mouth has been annealed.  Brass manufacturers are aware of the case cosmetics and have worked to mitigate it, but due to equipment design, denting may still occur.  Minor dents are normally removed in the first firing and will not affect case life or performance.  On non-plated brass, you may also notice all the anneal stain might not be polished off, which may give the case neck a pinkish color.  With some smaller caliber cases you may notice the case mouths to be slightly belled.

    With all new rifle brass, you should first straighten out the case and case mouth, then chamfer and debur the case mouth inside and out.  To straighten the case mouth, run the case part way into the sizer die and let the expander ball straighten the brass.  To prevent the case neck from stretching, be sure to lubricate the case neck inside the case mouth.

    If you are using Nickel plated brass, special care must be taken to lubricate the cases prior to sizing them.  Nickel plating is harder than brass and the cases require more effort in sizing.  In the event a case becomes stuck, purchase a stuck case remover; don’t use pliers, screwdrivers or other common household tools which could damage your sizing die.

    CAD $75.60
    Add to cart

    Remington Brass 270 Winchester Short Magnum (WSM) Bag of 50

    CAD $75.60 Add to cart
  • Winchester Brass 243 Winchester Super Short Magnum (WSSM) Bag of 50

    Winchester Brass 243 Winchester Super Short Magnum (WSSM) Bag of 50

    Winchester Reloading Brass is manufactured to extremely tight tolerances to ensure smooth feeding and positive chambering. Consistent case-to-case weight and capacity delivers outstanding accuracy. Winchester’s high quality, durable brass can be reloaded several times. New, unprimed brass. This is not loaded ammunition.

    Brass Preparation: With bulk rifle brass you may sometimes notice a few case mouths are “out of round” or slightly dented below the shoulder.  These imperfections occur in the final tumbling wash operation after the case mouth has been annealed.  Brass manufacturers are aware of the case cosmetics and have worked to mitigate it, but due to equipment design, denting may still occur.  Minor dents are normally removed in the first firing and will not affect case life or performance.  On non-plated brass, you may also notice all the anneal stain might not be polished off, which may give the case neck a pinkish color.  With some smaller caliber cases you may notice the case mouths to be slightly belled.

    With all new rifle brass, you should first straighten out the case and case mouth, then chamfer and debur the case mouth inside and out.  To straighten the case mouth, run the case part way into the sizer die and let the expander ball straighten the brass.  To prevent the case neck from stretching, be sure to lubricate the case neck inside the case mouth.

    If you are using Nickel plated brass, special care must be taken to lubricate the cases prior to sizing them.  Nickel plating is harder than brass and the cases require more effort in sizing.  In the event a case becomes stuck, purchase a stuck case remover; don’t use pliers, screwdrivers or other common household tools which could damage your sizing die.

    CAD $75.60
    Add to cart

    Winchester Brass 243 Winchester Super Short Magnum (WSSM) Bag of 50

    CAD $75.60 Add to cart
  • Winchester Brass 264 Winchester Magnum Bag of 50

    Winchester Brass 264 Winchester Magnum Bag of 50

    Winchester Reloading Brass is manufactured to extremely tight tolerances to ensure smooth feeding and positive chambering. Consistent case-to-case weight and capacity delivers outstanding accuracy. Winchester’s high quality, durable brass can be reloaded several times. New, unprimed brass. This is not loaded ammunition.

    Brass Preparation: With bulk rifle brass you may sometimes notice a few case mouths are “out of round” or slightly dented below the shoulder.  These imperfections occur in the final tumbling wash operation after the case mouth has been annealed.  Brass manufacturers are aware of the case cosmetics and have worked to mitigate it, but due to equipment design, denting may still occur.  Minor dents are normally removed in the first firing and will not affect case life or performance.  On non-plated brass, you may also notice all the anneal stain might not be polished off, which may give the case neck a pinkish color.  With some smaller caliber cases you may notice the case mouths to be slightly belled.

    With all new rifle brass, you should first straighten out the case and case mouth, then chamfer and debur the case mouth inside and out.  To straighten the case mouth, run the case part way into the sizer die and let the expander ball straighten the brass.  To prevent the case neck from stretching, be sure to lubricate the case neck inside the case mouth.

    If you are using Nickel plated brass, special care must be taken to lubricate the cases prior to sizing them.  Nickel plating is harder than brass and the cases require more effort in sizing.  In the event a case becomes stuck, purchase a stuck case remover; don’t use pliers, screwdrivers or other common household tools which could damage your sizing die.

    CAD $75.60
    Add to cart

    Winchester Brass 264 Winchester Magnum Bag of 50

    CAD $75.60 Add to cart
  • Winchester Brass 223 Winchester Super Short Magnum (WSSM) Bag of 50

    Winchester Brass 223 Winchester Super Short Magnum (WSSM) Bag of 50

    Winchester Reloading Brass is manufactured to extremely tight tolerances to ensure smooth feeding and positive chambering. Consistent case-to-case weight and capacity delivers outstanding accuracy. Winchester’s high quality, durable brass can be reloaded several times. New, unprimed brass. This is not loaded ammunition.

    Brass Preparation: With bulk rifle brass you may sometimes notice a few case mouths are “out of round” or slightly dented below the shoulder.  These imperfections occur in the final tumbling wash operation after the case mouth has been annealed.  Brass manufacturers are aware of the case cosmetics and have worked to mitigate it, but due to equipment design, denting may still occur.  Minor dents are normally removed in the first firing and will not affect case life or performance.  On non-plated brass, you may also notice all the anneal stain might not be polished off, which may give the case neck a pinkish color.  With some smaller caliber cases you may notice the case mouths to be slightly belled.

    With all new rifle brass, you should first straighten out the case and case mouth, then chamfer and debur the case mouth inside and out.  To straighten the case mouth, run the case part way into the sizer die and let the expander ball straighten the brass.  To prevent the case neck from stretching, be sure to lubricate the case neck inside the case mouth.

    If you are using Nickel plated brass, special care must be taken to lubricate the cases prior to sizing them.  Nickel plating is harder than brass and the cases require more effort in sizing.  In the event a case becomes stuck, purchase a stuck case remover; don’t use pliers, screwdrivers or other common household tools which could damage your sizing die.

    CAD $75.60
    Add to cart

    Winchester Brass 223 Winchester Super Short Magnum (WSSM) Bag of 50

    CAD $75.60 Add to cart
  • Hornady Brass 444 Marlin Box of 50

    Hornady Brass 444 Marlin Box of 50

    Hornady produces brass with the same precision, attention to detail and focus on perfection that has made them a world leader in bullets. They measure their brass for consistent wall concentricity, tests pressure calibration to ensure uniform case expansion and hand-inspects each piece.

    This dedication to quality ensures proper seating of the bullet both in the case and in the chamber and consistent charges and pressures. The result is optimal velocity and repeatable accuracy from your cartridges. New, unprimed brass. This is not loaded ammunition.

     

    Brass Preparation: With bulk rifle brass you may sometimes notice a few case mouths are “out of round” or slightly dented below the shoulder.  These imperfections occur in the final tumbling wash operation after the case mouth has been annealed.  Brass manufacturers are aware of the case cosmetics and have worked to mitigate it, but due to equipment design, denting may still occur.  Minor dents are normally removed in the first firing and will not affect case life or performance.  On non-plated brass, you may also notice all the anneal stain might not be polished off, which may give the case neck a pinkish color.  With some smaller caliber cases you may notice the case mouths to be slightly belled.

    With all new rifle brass, you should first straighten out the case and case mouth, then chamfer and debur the case mouth inside and out.  To straighten the case mouth, run the case part way into the sizer die and let the expander ball straighten the brass.  To prevent the case neck from stretching, be sure to lubricate the case neck inside the case mouth.

    CAD $76.00
    Add to cart

    Hornady Brass 444 Marlin Box of 50

    CAD $76.00 Add to cart
  • Hodgdon VARGET®

    Hodgdon VARGET®

    Varget is an extruded propellant in the Hodgdon line of Extreme series of powders. Varget features small, extruded grains for uniform metering, is insensitive to hot and cold temperatures and produces higher energy for improved velocities over other powders in its burning-speed class.

    The powder ignites quickly and burns clean, translating into superb accuracy, higher scores and more clean, one-shot kills.

    Varget is the perfect powder for shooting the 223 Remington with heavy bullets in competitive matches. Outstanding performance and velocity can be obtained in such popular cartridges as the 22-250 Remington, 308 Winchester, 30-06, 375 H&H and many more.

    Available in 1 lb. and 8 lb. containers.

    Price range: CAD $76.15 through CAD $545.35
    Select options This product has multiple variants. The options may be chosen on the product page

    Hodgdon VARGET®

    Price range: CAD $76.15 through CAD $545.35 Select options This product has multiple variants. The options may be chosen on the product page
  • Hodgdon H4831®

    Hodgdon H4831®

    H4831 is an extruded powder in Hodgdon’s Extreme series and it is probably safe to say more big-game animals have been taken by handloaders with H4831 than any other powder.

    Bruce “B.E.” Hodgdon was the first supplier to introduce this popular propellant in 1950 and, since that time, it has become a favorite for cartridges like the 270 Winchester, 25-06 Remington, 280 Remington and 300 Winchester Magnum.

    As an Extreme Extruded propellant, it shares the fine quality of insensitivity to hot and cold temperatures, as well as superb uniformity from lot to lot.

    Available in 1 lb. and 8 lb. containers.

    Price range: CAD $76.15 through CAD $553.51
    Select options This product has multiple variants. The options may be chosen on the product page

    Hodgdon H4831®

    Price range: CAD $76.15 through CAD $553.51 Select options This product has multiple variants. The options may be chosen on the product page
  • IMR Enduron® 8133

    IMR Enduron® 8133

    IMR Enduron 8133 is the slowest burn rate in the Enduron family. Loading density is perfect for magnums, contributing to superb uniformity. This is a true magnum propellant yielding outstanding performance in 6.5-300 Weatherby, 264 Win Mag, 28 Nosler and 300 Rem Ultra Mag, among other cartridges. Loading density is perfect for magnums, nicely filling the case at maximum charges, contributing to superb uniformity and accuracy.

    The main features of the Enduron series are copper fouling eliminator, insensitivity to temperature changes, ideal loading density and being environmentally friendly.

    IMR 8133 performs comparably to Hodgdon Retumbo but charge weights are materially different.

    IMR recommends always consulting www.IMRReloading.com for the most accurate, up-to-date data.

    Available in 1-LB and 8-LB containers.

    Price range: CAD $76.15 through CAD $507.27
    Select options This product has multiple variants. The options may be chosen on the product page

    IMR Enduron® 8133

    Price range: CAD $76.15 through CAD $507.27 Select options This product has multiple variants. The options may be chosen on the product page
  • IMR Green™

    IMR Green™

    This product has been discontinued.

    IMR Green is one of a new IMR family of powders that have comparable burn speeds to competitor powders. This new IMR family uses new, modern technology to ensure the product is “green,” burns clean and, in most cases, results in more energy from each grain of powder. IMR powders are consistent in bulk densities from lot to lot, eliminating some of the variability inherent in other competitors.

    IMR Green burns slightly slower than IMR RED, making it an ideal handicap trap powder and a favorite with sporting clays enthusiasts. This allows the shooter to reach maximum velocity with heavy 1- 1/8-oz. target loads. Accommodates loads from 7/8 to 1-1/8 -oz. 12-gauge loads. Produces excellent light 3⁄4-oz., 20- gauge target loads, especially in Remington STS and Winchester AA HS shells.

    For shotshell usage, powder densities are similar to competitor data. Most shotshell data is similar, but IMR recommends always consulting www.IMRReloading.com for the correct, up-to-date data and bushing charts.

    Price range: CAD $76.15 through CAD $344.07
    Select options This product has multiple variants. The options may be chosen on the product page

    IMR Green™

    Price range: CAD $76.15 through CAD $344.07 Select options This product has multiple variants. The options may be chosen on the product page
  • IMR Enduron® 7977

    IMR Enduron® 7977

    IMR Enduron 7977 is a slower burn rate in the Enduron family. Loading density is perfect for magnums, contributing to superb uniformity. This is a true magnum propellant yielding outstanding performance in 300 Winchester Magnum, 7mm Remington Magnum and 338 Lapua, among other cartridges. Loading density is perfect for magnums, nicely filling the case at maximum charges, contributing to superb uniformity and accuracy.

    The main features of the Enduron series are copper fouling eliminator, insensitivity to temperature changes, ideal loading density and being environmentally friendly.

    IMR 7977 performs comparably to Hodgdon H1000 but charge weights are materially different.

    IMR recommends always consulting www.IMRReloading.com for the most accurate, up-to-date data.

    Available in 1-LB and 8-LB containers.

    Price range: CAD $76.15 through CAD $504.55
    Select options This product has multiple variants. The options may be chosen on the product page

    IMR Enduron® 7977

    Price range: CAD $76.15 through CAD $504.55 Select options This product has multiple variants. The options may be chosen on the product page
  • Blackhorn 209

    Blackhorn 209

    Blackhorn 209 is a low residue, high performance propellant made for muzzleloaders and black powder cartridges. It is engineered to consistently shoot at higher velocities and with greater accuracy than any other muzzleloader powder available today.

    Price range: CAD $76.15 through CAD $456.95
    Select options This product has multiple variants. The options may be chosen on the product page

    Blackhorn 209

    Price range: CAD $76.15 through CAD $456.95 Select options This product has multiple variants. The options may be chosen on the product page
  • Norma Brass Shooters Pack 17 Remington Box of 50

    Norma Brass Shooters Pack 17 Remington Box of 50

    Norma Shooter’s Pack brass is packaged by Norma in convenient quantities. Norma USA Brass is world renowned as being the absolute highest quality brass available. These cases start off with the best possible raw materials with the narrowest tolerances. The case necks are annealed to soften the brass and prevent gas leaks the case body is at the optimum hardness to avoid any unnecessary stretching. New, unprimed brass that features chamfered and deburred case mouths and a punched flash hole (magnum calibers are drilled). These cases should be sized before loading. This is not loaded ammunition.

    Brass Preparation: With bulk rifle brass you may sometimes notice a few case mouths are “out of round” or slightly dented below the shoulder.  These imperfections occur in the final tumbling wash operation after the case mouth has been annealed.  Brass manufacturers are aware of the case cosmetics and have worked to mitigate it, but due to equipment design, denting may still occur.  Minor dents are normally removed in the first firing and will not affect case life or performance.  On non-plated brass, you may also notice all the anneal stain might not be polished off, which may give the case neck a pinkish color.  With some smaller caliber cases you may notice the case mouths to be slightly belled.

    With all new rifle brass, you should first straighten out the case and case mouth, then chamfer and debur the case mouth inside and out.  To straighten the case mouth, run the case part way into the sizer die and let the expander ball straighten the brass.  To prevent the case neck from stretching, be sure to lubricate the case neck inside the case mouth.

    CAD $77.52
    Add to cart

    Norma Brass Shooters Pack 17 Remington Box of 50

    CAD $77.52 Add to cart
  • Starline Brass 30-30 Winchester

    Starline Brass 30-30 Winchester

    Starline Brass prides itself on producing the highest quality brass case available. Their brass is comprised of 70% copper and 30% zinc and is vertically drawn during the manufacturing process which results in more uniform wall thickness. Cases are annealed between each draw to ensure consistent metallurgy in all lots. Each brass case is hand inspected to guarantee the highest quality possible.

    Starline Brass is located in Sedalia, MO and has been in business for over 30 years. Trust Starline for your next reloads, you won’t be disappointed. New, unprimed brass. This is not loaded ammunition. Bulk brass should be full-length sized, trimmed and chamfered before loading.

    Brass Preparation: With bulk rifle brass you may sometimes notice a few case mouths are “out of round” or slightly dented below the shoulder.  These imperfections occur in the final tumbling wash operation after the case mouth has been annealed.  Brass manufacturers are aware of the case cosmetics and have worked to mitigate it, but due to equipment design, denting may still occur.  Minor dents are normally removed in the first firing and will not affect case life or performance.  On non-plated brass, you may also notice all the anneal stain might not be polished off, which may give the case neck a pinkish color.  With some smaller caliber cases you may notice the case mouths to be slightly belled.

    With all new rifle brass, you should first straighten out the case and case mouth, then chamfer and debur the case mouth inside and out.  To straighten the case mouth, run the case part way into the sizer die and let the expander ball straighten the brass.  To prevent the case neck from stretching, be sure to lubricate the case neck inside the case mouth.

    If you are using Nickel plated brass, special care must be taken to lubricate the cases prior to sizing them.  Nickel plating is harder than brass and the cases require more effort in sizing.  In the event a case becomes stuck, purchase a stuck case remover; don’t use pliers, screwdrivers or other common household tools which could damage your sizing die.

    CAD $78.88
    Add to cart

    Starline Brass 30-30 Winchester

    CAD $78.88 Add to cart

Main Menu